Carbs - Quality re-manufactured / rebuilt carbs and
setups.  Specializing in Stromberg 97 / 48 / 81's
Phone: 913-244-0112
email:
rickshelton@gasalleystreetrods.
com
Mr Stromberg
Accelerator pump - 81 -What a beauty. With with correct Stromberg 81 10-finger brass spring washer and genuine leather seal. If you need new springs, washers, retainer and more, choose 9631K-81.
$15.95
code
9631k-81
Accelerator pump - 97/48/40 -Accelerator pump for Stromberg 97, 48 and 40 with correct length and leather seal. If you need new springs, washers, retainer and more, choose 9631K.
$9.95
code
9631k-97
Accelerator pump check valve-Hides under the center bowl plug and allows the accelerator pump to suck gas in, but not back out into the float bowl. Comes in the Premium Service kit (9590K).
$5.95
code
9573k
Accelerator pump discharge jets -When you gas it, this is where they squirt. So if they're blocked, you're in trouble. We're not going to lie to you. They're difficult to get out and a pig to get back in!
$19.95
code
9577K
Accelerator pump kit - 81 -Talk about original. Our Stromberg 81 accelerator pump has the correct 10-finger brass spring washer and small bore leather seal. The kit includes new springs, retainer, washers, felt gasket and cotter pin.
$25.95
code
9630k-81
Accelerator pump lever kit -Connects the accelerator pump rod to the actual pump. A beautiful investment cast stainless steel piece, with new spring and a cotter pin for the pump.
$19.95
code
9531k
Accelerator pump rod - 48/40 -All stainless steel with the correct swaged ends. Check you have the right size. This one is shorter because the 48 and 40 models have a different throttle shaft end bracket – without the S and W options.
$19.95
code
9526k-48
Accelerator pump rod - 97/81-All stainless steel with the correct swaged ends. Check you have the right size. This one is longer because the later 97 and 81 models have the improved throttle shaft end bracket with Summer and Winter choices.
$19.95
code
9526k-97
Airhorn fulcrum screw kit -One holds the choke lever (9552K) on. The other fixes the accelerator pump lever (9531K). One of each. Both stainless steel.
$11.95
9592k
code
Premium service kit - 81 -The best service kit available for your Genuine Stromberg 81. Comes with a full gasket kit, Stromberg S-jet inlet valve, accelerator pump check valve, two idle mixture screws and springs, full 81-size accelerator pump kit (with correct leather seal and springs), and a detailed Installation Guide.
$49.95
code
9590K-81
Premium service kit - 97/48/40-The best service kit available for your Stromberg 97, 48 or 40 carburetor. Comes with a full gasket kit, Stromberg S-jet inlet valve, accelerator pump check valve, two idle mixture screws and springs, full accelerator pump kit with new springs, and a detailed Installation Guide.
$45.95
code
9590K-97
S-jet inlet valve -The Genuine Stromberg twin-ball S-jet is the 'next generation' needle and seat. It's designed to eject dirt particles and improve high speed running and, unlike many a so-called viton-tipped needle valve, it won't stick or melt in today's corrosive new gas formulas. Comes with a new fibre washer. Fits Stromberg 97, 48, 81 and 40.
$16.95
code
9564k
S-jet inlet valve for 5/16in line -A specially designed S-jet inlet valve for use with 5/16in OD Stromberg Big Bore fuel lines - eg 9146-BIG 3x2 line for Small Block Chevy (standard 97 carburetors only accept 1/4in line).
$16.95
code
9564K-BIG
SuperSeat hose fitting-Only brass hose end available with the correct 18 degree seat Fits old Stromberg needle and seat, and new S-jet Also fits 9564K-BIG S-jet (standard on BIG 97 carbs) Tightens right into S-jet so no ugly threads showing Big 9/16 AF hex Perfect for 5/16in and 3/8in ID hose
$7.50
code
9080K
S-jet inlet valve for 5/16in line. Chrome -A specially designed S-jet inlet valve (in chrome) for use with 5/16in OD Stromberg Big Bore fuel lines - eg 9146-BIG 3x2 line for Small Block Chevy.
$21.45
code
9564K-BIG-C
SuperSeat hose fitting - chromed-Only brass hose end available with the correct 18 degree seat Chromed the traditional way! Fits old Stromberg needle and seat, and new S-jet Also fits 9564K-BIG S-jet (standard on BIG 97 carbs) Tightens right into S-jet so no ugly threads showing Perfect for 5/16in and 3/8in ID hose
$11.95
code
9080K-CHR
Throttle shaft and bush kit -Look at your throttle shaft. It's 70 years old, worn to hell and causing a vacuum leak! This is the 97/81 style, but it works with 48 and 40 models if you use the 9526-97 accelerator pump rod. The bushes compress on installation so ream them through (0.278inch) to insure the correct clearance.
$35.95
code
9581K
Throttle plates -If they're worn on one carburetor, it's tricky to set a stable idle. If you've got three carbs - go figure. These have the correct 7 degree edge so they don't stick in the throttle bore. Comes as a pair.
$13.95
code
9585k
LZ Push style Shaft and bush kit -An exact replica of the original Lincoln Zephyr throttle shaft and lever. Designed for LZ and '49 to '51 Mercury applications where the pedal pushes the lever. (Ford pedals pull, of course.) The bushes compress on installation so ream them through (0.278inch) to insure the correct clearance.
$39.95
code
9581K-LZ-1
Throttle/choke plate screws x 10 -If you're removing the choke or throttle plates, new screws are a must. The hollow ends allow them to be staked on the back to prevent shaking loose.
$5.95
code
9586k
New 97 base with vacuum port -New 97 base with ported vacuum fitting Provides ported vacuum for your distributor All new and complete with throttle shaft and plates, kicker, choke lever and idle mixture screws. One one vacuum port required per engine. Not compatible with the 1949-53 Ford flathead Loadamatic distributor
$149.00
code
9514-VP
Choke plate kit -You need this kit too! A new stainless steel plate with the correct 15 deg edge and brass flapper valve. Two new screws too.
$12.95
code
9549k
Choke shaft kit -All Stombergs run better with the chokes in, so if yours is missing, you need this kit. A new picture is on the way as it now comes with the end lever riveted to the shaft. The wave washer goes at the choke lever end.
$18.95
code
9546K
Spring kit -All the exterior springs - all stainless steel.
$18.95
code
9571k
Emulsion tubes - pair -If your emulsion tubes are blocked or crushed, your engine is never going to run properly. A super-precision piece to fit 97, 48, 81, 40 and LZ carburetors. No Stromberg rebuild is complete without these beauties.
$22.95
code
9534k
Bulk gasket kit -Full gasket kits (as 9447K above) but five whole sets.
$45.95
code
9447k-5
Full gasket kit-Fits Stromberg 97, 81, 48, and 40. Three main gaskets (high tech cellulose/nitrile mix), plus a new felt gasket for the accelerator pump, and fibre ring gaskets for the power valve, inlet valve and drain plugs (5 - 2 spare).
$10.95
code
9447k
Carb to manifold gasket 6-pack -Six gaskets in a handy pack. Always replace the gasket if you remove the carburetor from the intake.
$11.95
code
69447K
Choke lever detent and spring -97 and 81 models have this small pin which presses against the choke lever to provide a positive stop when the choke is off. 48 and 40 models don't use one. Comes with a new spring – all stainless steel.
$5.95
code
9537k
Choke lock detent kit -Most Strombergs – even in multiples - run better with the choke plates in. But who needs rattling levers? Lock them open with this clever detent pin – press one end into your choke lever, and the other end into your spring then install it into the airhorn just like the stock item.
$6.95
code
9537K-L
Accelerator pump kit - 97/48/40-Full accelerator pump kit for Stromberg 97, 48 and 40 carburetors. Includes new springs, retainer, washers, felt gasket and cotter pin.
$19.95
code
9630k-97
Throttle stop screw kit -Fits in the kicker linkage. Used to set your idle speed. New screw and spring. All stainless steel.
$5.95
9589k
code
Idle mixture screw kit -Included in our Premium Service Kits (9590K) but also separately here. Two new screws with stainless steel springs.
$12.95
code
9541k
Bowl gallery plugs -There are tiny lead plugs in most of the old Stromberg models, used to seal various passages after machining. Ours are a more environmentally friendly tin alloy, but they work just the same. A pack of 20.
$9.95
code
9523K
Bowl plug kit -Three brass plugs from under the float bowl with gaskets.
$19.95
code
9522k
Bowl plug gaskets x 10-If your Stromberg is leaking from underneath, these could be the answer.
$4.95
code
9563k
Brass float with hinge pin -Fits 97, 81, 48, 40 and other models too. Made on the original Stromberg tooling. Pressure tested, of course, and supplied with a new float hinge pin.
$21.95
code
9550k
Float hinge pin -It sits below the fuel line - hence that fine thread. If yours leaks, it's because the thread is worn.
$5.95
code
9558k
Brass Fuel Inlet Repair Insert - Don't throw that precious Stromberg away because of striped fuel inlet threads repair it with our repair kit which includes insert, 9/16-18 tap, 33/64 drill bit, and instructions. This is not a helicoil this is a solid brass insert!
$56.95
code
fuelinletrepairkit
Brass Fuel Inlet Repair Insert - These brass inserts are used to repair the damaged or stripped fuel inlet threads on Stromberg 97/81/48 bodies. Use a 33/64 drill and 9/16-18 tap or buy our complete repair kit below. (Priced each).
$24.95
inletinsert
code
Phenolic carburetor spacer - 1/4in
$29.95
code
39447K
Carb block off plate -Want to keep a carb or two out of action? Slip this thin stainless plate between the carb and gasket. It's shaped to fit the carburetor base footprint, but it's smaller so it all but disappears. You don't need extended intake studs either.
$12.95
code
29447K
Cable Throttle Bracket-Mounts your hot rod cable throttle kit Accepts hot rod auto-trans kickdown cable kits Separate mount for traditional throttle return springs. All stainless steel Comes with new Stromberg carb-to-manifold gasket Does not require extended intake manifold studs.
$39.95
code
9136K
Kicker assembly -Kicks the throttle open just a little when you shut the choke plate. If yours was cut short and brazed onto the base basting, now's the time to put the choke back and get that carburetor working properly. All stainless steel with the correct numbers. Includes a new idle screw & spring.
$35.95
code
9552k
Choke cable mounting bracket -A perfect replica - in stainless steel - of the cable choke mounting bracket that came with '49-'53 Fords. This separate bracket (included with our 9510A-C cable choke carburetor) - mounts off the rear body screw to hold the choke cable sleeve.
$21.95
code
9552K-B
Kicker assembly for cable choke - with bracket -A perfect replica - in stainless steel - of the 97 kicker assembly for cable choke (designed for '49-53 Fords). A separate bracket - included - mounts off the rear body screw to hold the choke cable sleeve.
$49.95
code
9552k-c
Manifold stud kit (3) -Three intake manifold studs with stainless lock washers and nuts.
$12.95
code
89067K
Extended intake manifold stud kit (3) -Fitting some Stromberg Phenolic spacers (39447k)? Then you will need these 1/4in extended intake manifold studs. Comes with stainless nuts and lock washers, of course.
$13.95
code
89067K-E
Premium jet wrench-Stainless steel with knurls for good grip and a CNC milled end for a super fit. Cheaper wrenches have a punched end. This will last a lifetime.
$29.95
code
9071K
Main jets - 0.033in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-33
Main jets - 0.035in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-35
Main jets - 0.036in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-36
Main jets - 0.037in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-37
Main jets - 0.038in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-38
Main jets - 0.039in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-39
Main jets - 0.040in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-40
Main jets - 0.041in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-41
Main jets - 0.042in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-42
Main jets - 0.043in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-43
Main jets - 0.044in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-44
Main jets - 0.045in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-45
Main jets - 0.046in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-46
Main jets - 0.047in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-47
Main jets - 0.048in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-48
Main jets - 0.049in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-49
Main jets - 0.050in-Fits Stromberg 97, 81, 48, 40, LZ and other models. Two jets. Installs with Genuine Stromberg jet wrench - 9071K. Click on Tech Center for jetting advice.
$9.95
code
9533K-50
Stromberg Jet Wrench - Stromberg Jet Wrench - just what you need to change your new jets!
$17.95
code
SWStrombergJetWrench
Power valve - No.60 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-60
Power valve - No.61 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-61
Power valve - No.62 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-62
Power valve - No.63 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-63
Power valve - No.64 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-64
Power valve - No.65 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-65
Power valve - No.66 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-66
Power valve - No.67 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-67
Power valve - No.68 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-68
Power valve - No.69 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-69
Power valve - No.70 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-70
Power valve - No.71 - Fits Stromberg 97, 81, 48, 40, LZ and other models. Comes with new fibre gasket. Click on Tech Center for jetting advice.
$12.95
code
9594k-71
email:
rickshelton@gasalleystreetrods.
com